View M29W040_173911.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

M29W040
4 Mbit (512Kb x8, Uniform Block) Low Voltage Single Supply Flash Memory
NOT FOR NEW DESIGN
M29W040 is replaced by the M29W040B 2.7V to 3.6V SUPPLY VOLTAGE for PROGRAM, ERASE and READ OPERATIONS FAST ACCESS TIME: 100ns BYTE PROGRAMMING TIME: 12s typical ERASE TIME - Block: 1.5 sec typical - Chip: 2.5 sec typical PROGRAM/ERASE CONTROLLER (P/E.C.) - Program Byte-by-Byte - Data Polling and Toggle bits Protocol for P/E.C. Status MEMORY ERASE in BLOCKS - 8 Uniform Blocks of 64 KBytes each - Block Protection - Multiblock Erase ERASE SUSPEND and RESUME MODES LOW POWER CONSUMPTION - Read mode: 8mA typical (at 12MHz) - Stand-by mode: 20A typical - Automatic Stand-by mode POWER DOWN SOFTWARE COMMAND - Power-down mode: 1A typical 100,000 PROGRAM/ERASE CYCLES per BLOCK 20 YEARS DATA RETENTION - Defectivity below 1ppm/year ELECTRONIC SIGNATURE - Manufacturer Code: 20h - Device Code: E3h Table 1. Signal Names
A0-A18 DQ0-DQ7 E G W VCC VSS Address Inputs Data Input / Outputs Chip Enable Output Enable Write Enable Supply Voltage Ground
PLCC32 (K)
TSOP32 (N) 8 x 20mm
TSOP32 (NZ) 8 x 14mm
Figure 1. Logic Diagram
VCC
19 A0-A18
8 DQ0-DQ7
W E G
M29W040
VSS
AI02074
November 1999
This is information on a product still in productionbut not recommended for new designs.
1/31
M29W040
Figure 2A. LCC Pin Connections Figure 2B. TSOP Pin Connections
1 32 A7 A6 A5 A4 A3 A2 A1 A0 DQ0 A14 A13 A8 A9 A11 G A10 E DQ7
9
M29W040
25
17 DQ1 DQ2 VSS DQ3 DQ4 DQ5 DQ6
AI02075
A11 A9 A8 A13 A14 A17 W VCC A18 A16 A15 A12 A7 A6 A5 A4
A12 A15 A16 A18 VCC W A17
1
32
8 9
M29W040 (Normal)
25 24
16
17
AI02076
G A10 E DQ7 DQ6 DQ5 DQ4 DQ3 VSS DQ2 DQ1 DQ0 A0 A1 A2 A3
Figure 2C. TSOP Reverse Pin Connections
G A10 E DQ7 DQ6 DQ5 DQ4 DQ3 VSS DQ2 DQ1 DQ0 A0 A1 A2 A3
1
32
8 9
M29W040 (Reverse)
25 24
16
17
AI02077
A11 A9 A8 A13 A14 A17 W VCC A18 A16 A15 A12 A7 A6 A5 A4
DESCRIPTION The M29W040 is a non-volatile memory that may be erased electrically at the block level, and programmed Byte-by-Byte. The interface is directly compatible with most microprocessors. PLCC32, TSOP32 (8 x 20mm)and TSOP32 (8 x 14mm) packages are available. Both normal and reverse pin outs are available for the TSOP32 (8 x 20mm) package. Organisation The FlashMemory organisationis 512K x8 bits with Address lines A0-A18 and Data Inputs/Outputs DQ0-DQ7. Memory control is provided by Chip Enable, Output Enable and Write Enable Inputs. Erase and Program are performed through the internal Program/Erase Controller (P/E.C.). Data Outputs bits DQ7 and DQ6 provide polling or toggle signals during Automatic Program or Erase to indicate the Ready/Busy state of the internal Program/Erase Controller. Memory Blocks Erasure of the memory is in blocks. There are 8 uniform blocks of 64 Kbytes each in the memory address space. Each block can be programmed and erased over 100,000 cycles. Each uniform
2/31
M29W040
Table 2. Absolute Maximum Ratings (1)
Symbol TA TBIAS TSTG VIO
(2)
Parameter Ambient Operating Temperature Temperature Under Bias Storage Temperature Input or Output Voltages Supply Voltage A9 Voltage
(3)
Value -40 to 85 -50 to 125 -65 to 150 -0.6 to 5 -0.6 to 5 -0.6 to 13.5
Unit C C C V V V
VCC VA9
(2)
Notes: 1. Except for the rating "Operating Temperature Range", stresses above those listed in the Table "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only and operation of the device at these or any other conditions above those indicated in the Operating sections of this specification is not implied. Exposure to Absolute Maximum Rating conditions for extended periods may affect device reliability. Refer also to the STMicroelectronics SURE Program and other relevant quality documents. 2. Minimum Voltage may undershoot to -2V during transition and for less than 20ns. 3. Depends on range.
block may separately be protected and unprotected against program and erase. Block erasure may be suspended, while data is read from other blocks of the memory, and then resumed. Bus Operations Seven operations can be performed by the appropriate bus cycles, Read Array, Read Electronic Signature, Output Disable, Standby,Protect Block, Unprotect Block, and Write the Command of an Instruction. Command Interface Command Bytes can be written to a Command Interface (C.I.) latch to perform Reading (from the Array or Electronic Signature), Erasure or Programming. For added data protection, command execution starts after 4 or 6 command cycles. The first, second, fourth and fifth cycles are used to input a code sequence to the Command Interface (C.I.). This sequence is equal for all P/E.C. instructions. Command itself and its confirmation - if it applies - are given on the third and fourth or sixth cycles. Instructions Eight instructions are defined to perform Reset, Read Electronic Signature, Auto Program, Block Auto Erase, Chip Auto Erase, Block Erase Suspend, Block Erase Resume and Power Down. The internal Program/EraseController (P/E.C.) handles all timing and verification of the Program and Erase
instructions and provides Data Polling, Toggle, and Status data to indicate completion of Program and Erase Operations. Instructions are composed of up to six cycles. The first two cycles input a code sequence to the Command Interface which is common to all P/E.C. instructions (see Table 7 for Command Descriptions). The third cycle inputs the instruction set up command instruction to the Command Interface. Subsequentcycles output Signature,Block Protection or the addressed data for Read operations. For added data protection, the instructions for program, and block or chip erase require further command inputs. For a Program instruction, the fourth command cycle inputs the address and data to be programmed. For an Erase instruction (block or chip), the fourth and fifth cycles input a further code sequence before the Erase confirm command on the sixth cycle. Byte programming takes typically 12s while erase is performed in typically 1.5 second. Erasure of a memory block may be suspended, in order to read data from another block, and then resumed. Data Polling, Toggle and Error data may be read at any time, including during the programming or erase cycles, to monitor the progress of the operation.When power is first applied or if VCC falls below VLKO , the command interface is reset to Read Array.
3/31
M29W040
Table 3. Operations
Operation Read Write Output Disable Standby
Note: X = VIL or VIH
E VIL VIL VIL VIH
G VIL VIH VIH X
W VIH VIL VIH X
DQ0 - DQ7 Data Output Data Input Hi-Z Hi-Z
Table 4. Electronic Signature
Code Manufact. Code Device Code E VIL VIL G VIL VIL W VIH VIH A0 VIL VIH A1 VIL VIL A6 VIL VIL A9 VID VID Other Addresses Don't Care Don't Care DQ0 - DQ7 20h E3h
Table 5. Block Protection Status
Code Protected Block Unprotected Block E VIL VIL G VIL VIL W VIH VIH A0 VIL VIL A1 VIH VIH A6 VIL VIL A16 SA SA A17 SA SA A18 SA SA Other Addresses Don't Care Don't Care DQ0 - DQ7 01h 00h
Note: SA = Address of block being checked
DEVICE OPERATION Signal Descriptions Address Inputs (A0-A18). The address inputs for the memory array are latched during a write operation. The A9 address input is used also for the Electronic Signature read and Block Protect verification. When A9 is raised to VID, either a Read Manufacturer Code, Read Device Code or Verify Block Protection is enabled dependingon the combination of levels on A0, A1 and A6. When A0, A1 and A6 are Low, the ElectronicSignature Manufacturer code is read, when A0 is High and A1 and A6 are Low, the Device code is read, and when A1 is High and A0 and A6 are low, the Block Protection Status with protect/unprotect algorithm is read for the block addressed by A16, A17, A18. Data Input/Outputs (DQ0-DQ7). The data input is a byte to be programmed or a command written to the C.I. Both are latched when Chip Enable E and Write Enable W are active. The data output is from the memory Array, the Electronic Signature, the Data Polling bit (DQ7), the Toggle Bit (DQ6), the Error bit (DQ5) or the Erase Timer bit (DQ3). Ouputs are valid when Chip Enable E and Output Enable G are active. The output is high impedance
when the chip is deselected or the outputs are disabled. Chip Enable (E). The Chip Enable activates the memory control logic, input buffers, decoders and sense amplifiers. E High deselectsthe memory and reduces the power consumption to the standby level. E can also be used to control writing to the command register and to the memory array, while W remains at a low level. Addresses are then latchedon the falling edge of E while data is latched on the rising edge of E. The Chip Enable must be forced to VID during Block Unprotect operations. Output Enable (G). The Output Enable gates the outputs through the data buffers during a read operation. G must be forced to VID level during Block Protect and Block Unprotect operations. Write Enable (W). This input controls writing to the Command Register and Address and Data latches. Addressesare latchedon the fallingedge of W, and Data Inputs are latched on the rising edge of W. VCC Supply Voltage. The power supply for all operations (Read, Program and Erase). VSS Ground. VSS is the reference for all voltage measurements.
4/31
M29W040
Table 6. Instructions (1)
Mne. Instr. Cyc. 1+ RST
(3,9)
1st Cyc. 2nd Cyc. 3rd Cyc. 4th Cyc. 5th Cyc. 6th Cyc. Addr. (2,6) Data X F0h 5555h AAh 5555h AAh 5555h AAh
(2,6)
7th Cyc.
Read Memory Array until a new write cycle is initiated.
Read Array/ Reset 3+
Addr. (2,6) Data
2AAAh 55h 2AAAh 55h 2AAAh 55h 2AAAh
5555h F0h 5555h 90h 5555h 90h 5555h
Read Memory Array until a new write cycle is initiated.
Read RSIG (3) Electronic Signature Read Block Protection
Addr. (2,6) 3+ Data Addr. (2,6) Data Addr.
Read Electronic Signature until a new write cycle is initiated. See Note 4.
RBP
(3)
3+
Read Block Protection until a new write cycle is initiated. See Note 5. Program Address Read Data Polling or Toggle Bit until Program completes. Program Data 5555h AAh 5555h AAh 2AAAh 55h 2AAAh 55h Block Address 30h 5555h 10h Additional Block (7) 30h Note 8
5555h
PG
Program
4 Data
(2,6)
AAh
55h
A0h
BE
Block Erase
6
Addr. Data
5555h AAh 5555h AAh
2AAAh 55h 2AAAh 55h
5555h 80h 5555h 80h
CE
Chip Erase
6
Addr. (2,6) Data
ES
Erase Suspend
1
Addr. Data
(2,6)
X B0h X 30h 5555h 20h
Read until Toggle stops, then read all the data needed from any uniform block(s) not being erased then Resume Erase.
ER
Erase Resume
1
Addr. (2,6) Data
Read Data Polling or Toggle Bit until Erase completes or Erase is suspended another time
PD
(10)
Power Down
1
Addr. (2,6) Data
Puts the memory in Power Down mode where power consumption is reduced to typically less than 1A
Notes: 1. Command not interpreted in this table will default to read array mode. 2. X = Don't Care. 3. The first cycle of the RST, RBP or RSIG instruction is followed by read operations to read memory array, Status Register or Electronic Signature codes. Any number of read cycles can occur after one command cycle. 4. Signature Address bits A0, A1, A6 at VIL will output Manufacturer code (20h). Address bits A0 at VIH and A1, A6 at VIL will output Device code. 5. Protection Address: A0, A6 at VIL, A1 at VIH and A16, A17, A18 within the uniform block to be checked, will output the Block Protection status. 6. Address bits A15-A18 are don't care for coded address inputs. 7. Optional, additional blocks addresses must be entered within a 80s delay after last write entry, timeout status can be verified through DQ3 value. When full command is entered, read Data Polling or Toggle bit until Erase is completed or suspended. 8. Read Data Polling or Toggle bit until Erase completes. 9. A wait time of 5s is necessary after a Reset command, if the memory is in a Block Erase or Power Down status, before starting any operation. 10. Writing an RST command to the P/E.C. is mandatory prior to any new operation when the memory is in Power Down mode.
5/31
M29W040
Memory Blocks The memory blocks of the M29W040 are shown in Figure 3. The memory array is divided in 8 uniform blocks of 64 Kbytes. Each block can be erased separately or any combination of blocks can be erased simultaneously. The Block Erase operation is managed automaticallyby the P/E.C. The operation can be suspended in order to read from any other block, and then resumed. Block Protection provides additional data security. Each uniform block can be separately protected or unprotectedagainst Programor Erase. BringingA9 and G to VID initiates protection, while bringing A9, G and E to VID cancels the protection. The block affected during protection is addressed by the inputs on A16, A17, and A18. Unprotect operation affects all blocks. Operations Operations are defined as specific bus cycles and signals which allow Memory Read, Command Write, Output Disable, Standby, Read Status Bits, Block Protect/Unprotect, Block Protection Check and ElectronicSignature Read. They are shown in Tables 3, 4, 5. Read. Read operations are used to output the contents of the Memory Array, the Status Register or the Electronic Signature. Both Chip Enable E and Output Enable G must be low in order to read the output of the memory. The Chip Enable input also provides power control and shouldbe used for device selection. Output Enable should be used to gate dataonto the outputindependentof the device selection. The data read depends on the previous command written to the memory (see instructions RST and RSIG, and Status Bits). Write. Write operationsare used to give Instruction Commands to the memory or to latch input data to be programmed. A write operation is initiated when Chip Enable E is Low and Write Enable W is Low with Output Enable G High. Addresses are latched on the falling edge of W or E whicheveroccurs last. Commands and Input Data are latchedon the rising edge of W or E whichever occurs first. Output Disable. The data outputs are high impedance when the Output Enable G is High with Write Enable W High. Standby. The memory is in standby when Chip Enable E is High and Program/Erase Controller P/E.C. is Idle. The power consumption is reduced to the standby level and the outputs are high impedance, independent of the Output Enable G or Write Enable W inputs. Automatic Standby. After 150ns of inactivity and when CMOS levels are driving the addresses, the chip automatically enters a pseudo standby mode where consumption is reduced to the CMOS standby value, while outputs are still driving the bus. Power Down. When the PD command is written to the P/E.C. the memory enters a power down status where the power consumption is reduced to ICC6 (typically less than 1.0A). Electronic Signature. Two codes identifying the manufacturer and the device can be read from the memory, the manufacturer's code for STMicroelectronics is 20h, and the device code is E3h for the M29W040. These codes allow programming equipment or applications to automatically match their interface to the characteristics of the particular manufacturer's product. The Electronic Signature is output by a Read operation when the voltage applied to A9 is at VID and address inputs A1 and A6 are at Low. The manufacturer code is output when the Address input A0 is Low and the device code when this input is High. Other Address inputs are ignored. The codes are output on DQ0-DQ7. This is shown in Table 4. The Electronic Signature can also be read, without raising A9 to VID by giving the memory the instruction RSIG (see below).
6/31
M29W040
Figure 3. Memory Map and Block Address Table
A18 1 1 1 1 0 0 0 0
AI01362B
A17 1 1 0 0 1 1 0 0
A16 1 0 1 0 1 0 1 0 64K Bytes Block 64K Bytes Block 64K Bytes Block 64K Bytes Block 64K Bytes Block
TOP ADDRESS 7FFFFh 6FFFFh 5FFFFh 4FFFFh 3FFFFh 2FFFFh 1FFFFh 0FFFFh
BOTTOM ADDRESS 70000h 60000h 50000h 40000h 30000h 20000h 10000h 00000h
Block Protection. Each uniform block can be separately protected against Program or Erase. Block Protection provides additional data security, as it disables all program or erase operations. This mode is activated when both A9 and G are set to VID and the block address is applied on A16-A18. Block Protection is programmed using a Presto F program like algorithm. Protectionis initiated on the edge ofW falling to VIL. Then after a delayof 100s, the edge of W rising to VIH ends the protection operation. Protection verify is achieved by bringing G, E and A6 to VIL while W is at VIH and A9 at VID. Under these conditions, readingthe data output will yield 01h if the block defined by the inputs on A16-A18 is protected. Any attempt to program or erase a protected block will be ignored by the device. Any protected block can be unprotected to allow updating of bit contents. All blocks must be protected before an unprotect operation. Block Unprotect is activated when A9, G and E are at VID. The addresses inputs A6, A12, A16 must be maintained at VIH. Block Unprotect is performedthrough a Presto F Erase like algorithm. Unprotect is initiated by the edge of W falling to VIL. After a delay of 10ms, the edge of W rising to VIH will end the unprotection operation. Unprotect verify is achieved by bringing G and E to VIL while A6 and
Table 7. Commands
Hex Code 10h 20h 30h 50h 80h 90h A0h B0h F0h Command Chip Erase Confirm Power Down Block Erase Resume/Confirm Reserved Set-up Erase Read Electronic Signature/ Block Protection Status Program Erase Suspend Read Array/Reset
W are at VIH and A9 at VID. In these conditions, reading the output data will yield 00h if the block defined by the inputs on A16-A18 has been successfullyunprotected.All combinations of A16-A18 must be addressed in order to ensure that all of the 8 uniform blocks have been unprotected. Block Protection Status is shown in Table 5.
7/31
M29W040
Table 8. Status Register
DQ Name Logic Level '1' 7 Data Polling '0' DQ DQ '-1-0-1-0-1-0-1-' 6 Toggle Bit '-0-0-0-0-0-0-0-' '-1-1-1-1-1-1-1-' 5 Error Bit '1' '0' 4 '1' '0' '1' 3 Erase Time Bit '0' Erase Timeout Period Expired Erase Timeout Period on going P/E.C. Erase operation has started. Only possible command entry is Erase Suspend (ES). An additional block to be erased in parallel can be entered to the P/E.C. Definition Erase Complete Erase on going Program Complete Program on going Erase or Program on going Program ('0' on DQ6) Complete Erase or Program ('1' on DQ6) Complete Program or Erase Error Program or Erase on going Successive read output complementary data on DQ6 while Programming or Erase operations are going on. DQ6 remain at constant level when P/E.C. operations are completed or Erase Suspend is acknowledged. This bit is set to '1' if P/E.C. has exceded the specified time limits. Note Indicates the P/E.C. status, check during Program or Erase, and on completion before checking bits DQ5 for Program or Erase Success.
2 1 0
Reserved Reserved Reserved
Note: Logic level '1' is High, '0' is Low. -0-1-0-0-0-1-1-1-0- represent bit value in successive Read operations.
Instructions and Commands The Command Interface (C.I.) latches commands written to the memory. Instructions are made up from one or more commands to perform Read Array/Reset, Read Electronic Signature, Power Down, Block Erase, Chip Erase, Program, Block Erase Suspend and Erase Resume. Commands are made of address and data sequences. Addresses are latched on the falling edge of W or E and data is latched on the rising of W or E. The instructions require from 1 to 6 cycles, the first or first three of which are always write operations used to initiate the command. They are followed by either further write cycles to confirm the first command or execute the command immediately. Command sequencing must be followed exactly. Any invalid combination of commands will reset the device to Read Array. The increased number of cycles has been chosen to assure maximum data security. Commands are initialised by two preceding coded cycles which unlock the Command Interface. In addition, for Erase, command confirmation is again preceeded by the two coded cycles. P/E.C. status is indicated during command execution by Data Polling on DQ7, detectionof Toggle on
8/31
DQ6, or Error on DQ5 and Erase Timer DQ3 bits. Any read attempt during Program or Erase command executionwill automaticallyoutput those four bits. The P/E.C. automatically sets bits DQ3, DQ5, DQ6 and DQ7. Other bits (DQ0, DQ1, DQ2 and DQ4) are reserved for future use and should be masked. Data Polling bit (DQ7). When Programming operations are in progress, this bit outputs the complement of the bit being programmed on DQ7. During Erase operation, it outputs a '0'. After completion of the operation,DQ7 will output the bit last programmed or a '1' after erasing. Data Polling is valid only effective during P/E.C. operation, that is after the fourth W pulse for programming or after the sixth W pulse for Erase. It must be performed at the address being programmed or at an address within the block being erased. If the byte to be programmed belongs to a protectedblock the command is ignored. If all the blocks selected for erasure are protected, DQ7 will set to '0' for about 100s, and then return to previous addressed memory data. See Figure 9 for the Data Polling flowchart and Figure 10 for the Data Polling waveforms.
M29W040
Table 9. AC Measurement Conditions
Input Rise and Fall Times Input Pulse Voltages Input and Output Timing Ref. Voltages 10ns 0 to 3V 1.5V
1N914
Figure 5. AC Testing Load Circuit
0.8V
Figure 4. AC Testing Input Output Waveform
DEVICE UNDER TEST 1.5V 0V
AI01417
3.3k
OUT CL = 30pF or 100pF
3V
CL includes JIG capacitance
AI01968
Table 10. Capacitance (1) (TA = 25 C, f = 1 MHz )
Symbol CIN COUT Parameter Input Capacitance Output Capacitance Test Condition VIN = 0V VOUT = 0V Min Max 6 12 Unit pF pF
Note: 1. Sampled only, not 100% tested.
Table 11. DC Characteristics (TA = 0 to 70C, -20 to 85C or -40 to 85C; VCC = 2.7V to 3.6V)
Symbol ILI ILO ICC1 ICC2 ICC3 ICC4 ICC5 ICC6 VIL VIH VOL VOH VID IID VLKO Parameter Input Leakage Current Output Leakage Current Supply Current (Read) Supply Current (Standby) TTL Supply Current (Standby) CMOS Supply Current (Program or Erase) Supply Current Power Down Current Input Low Voltage Input High Voltage Output Low Voltage Output High Voltage CMOS A9 Voltage (Electronic Signature) A9 Current (Electronic Signature) Supply Voltage (Erase and Program lock-out) A9 = VID 1.9 IOL = 2mA IOH = -100A IOH = -2.0mA VCC -0.4 0.85 VCC 11.5 12.5 50 2.2 Test Condition 0V VIN VCC 0V VOUT VCC E = VIL, G = VIH, f = 6MHz E = VIH E = VCC 0.2V Byte Program, Block Erase Chip Erase in progress E = VCC 0.2V -0.5 0.7 VCC Min Max 1 1 20 0.2 50 20 40 5 0.8 VCC + 0.5 0.45 Unit A A mA mA A mA mA A V V V V V V A V
9/31
M29W040
Table 12A. Read AC Characteristics (TA = 0 to 70C, -20 to 85C or -40 to 85C)
M29W040 Symbol Alt Parameter Test Condition -100 -120 Unit
VCC = 3.3V0.3V VCC = 3.3V0.3V CL = 30pF Min tAVAV tAVQV tELQX tELQV
(1) (2)
Max
Min 120
Max ns 120 ns ns 120 ns ns 50 ns ns 30 ns ns 30 ns ns
tRC tACC tLZ tCE tOLZ tOE tOH tHZ tOH tDF tOH
Address Valid to Next Address Valid Address Valid to Output Valid Chip Enable Low to Output Transition Chip Enable Low to Output Valid Output Enable Low to Output Transition Output Enable Low to Output Valid Chip Enable High to Output Transition Chip Enable High to Output Hi-Z Output Enable High to Output Transition Output Enable High to Output Hi-Z Address Transition to Output Transition
E = VIL, G = VIL E = VIL, G = VIL G = VIL G = VIL E = VIL E = VIL G = VIL G = VIL E = VIL E = VIL E = VIL, G = VIL
100 100 0 100 0 40 0 20 0 20 0
0
tGLQX (1) tGLQV
(2)
0
tEHQX tEHQZ
(1)
0
tGHQX tGHQZ (1) tAXQX
0
0
Notes: 1. Sampled only, not 100% tested. 2. G may be delayed by up to tELQV - tGLQV after the falling edge of E without increasing tELQV.
Toggle bit (DQ6). When Programming operations are in progress, successive attempts to read DQ6 will output complementary data. DQ6 will toggle following toggling of either G or E when G is low. The operation is completed when two successive reads yield the same output data. The next read will output the bit last programmed or a '1' after erasing. The toggle bit is valid only effective during P/E.C. operations, that is after the fourth W pulse for programming or after the sixth W pulse for Erase. If the byte to be programmed belongs to a protected block the command will be ignored. If the blocks selected for erasure are protected, DQ6 will toggle for about 100s and then return back to Read. See Figure 11 for Toggle Bit flowchart and Figure 12 for Toggle Bit waveforms. Error bit (DQ5). This bit is set to '1' by the P/E.C when there is a failure of byte programming, block erase, or chip erase that results in invalid data being programmedin the memory block. In case of error in block erase or byte program, the block in which the error occured or to which the pro-
grammed byte belongs, must be discarded. Other blocks may still be used. Error bit resetsafter Reset (RST) instruction. In case of success, the error bit will set to '0' during Program or Erase and to valid data after write operation is completed. Erase Timer bit (DQ3). This bit is set to '0' by the P/E.C. when the last Block Erase command has been entered to the Command Interface and it is awaiting the Erase start. When the erase timeout period is finished, after 80 to 120s, DQ3 returns back to '1'. Coded Cycles. The two coded cycles unlock the Command Interface. They are followed by a command input or a comand confirmation. The coded cycles consist of writing the data AAh at address 5555h during the first cycle and data 55hat address 2AAAh during the second cycle. Addresses are latched on the falling edge of W or E while data is latched on the rising edge of W or E. The coded cycles happen on first and second cycles of the command write or on the fourth and fifth cycles.
10/31
M29W040
Table 12B. Read AC Characteristics (TA = 0 to 70C, -20 to 85C or -40 to 85C)
M29W040 Symbol Alt Parameter Test Condition -150 -200 Unit
VCC = 2.7V to 3.6V VCC = 2.7V to 3.6V Min tAVAV tAVQV tELQX (1) tELQV (2) tGLQX (1) tGLQV (2) tEHQX tEHQZ (1) tGHQX tGHQZ
(1)
Max
Min 200
Max ns 200 ns ns 200 ns ns 70 ns ns 50 ns ns 50 ns ns
tRC tACC tLZ tCE tOLZ tOE tOH tHZ tOH tDF tOH
Address Valid to Next Address Valid Address Valid to Output Valid Chip Enable Low to Output Transition Chip Enable Low to Output Valid Output Enable Low to Output Transition Output Enable Low to Output Valid Chip Enable High to Output Transition Chip Enable High to Output Hi-Z Output Enable High to Output Transition Output Enable High to Output Hi-Z Address Transition to Output Transition
E = VIL, G = VIL E = VIL, G = VIL G = VIL G = VIL E = VIL E = VIL G = VIL G = VIL E = VIL E = VIL E = VIL, G = VIL
150 150 0 150 0 55 0 40 0 40 0
0
0
0
0
tAXQX
0
Notes: 1. Sampled only, not 100% tested. 2. G may be delayed by up to tELQV - tGLQV after the falling edge of E without increasing tELQV.
Read Array/Reset (RST) instruction. The Reset instruction consists of one write operation giving the command F0h. It can be optionally preceded by the two coded cycles. A wait state of 5s before read operationsis necessaryif the Reset command is applied during an Erase or Power Down operation. Read Electronic Signature (RSIG) instruction. This instruction uses the two coded cycles followed by one write cycle giving the command 90h to address 5555h for command setup. A subsequent read will output the manufacturer code, the device code or the Block Protection status depending on the levels of A0, A1, A6, A16, A17 and A18. The manufacturer code, 20h, is output when the addresses lines A0, A1 and A6 are Low, the device code, E2h is output when A0 is High with A1 and A6 Low.
Read Block Protection (RBP) instruction. The use of Read ElectronicSignature(RSIG) command also allows access to the Block Protection status verify. After giving the RSIG command, A0 and A6 are set to VIL with A1 at VIH, while A16, A17 and A18 define the block of the block to be verified. A read in these conditions will output a 01h if block is protected and a 00h if block is not protected. This Read Block Protection is the only valid way to check the protection status of a block. Nevertheless, it must not be used during the block protection phase as a method to verify the Block Protection. Please refer to Block Protection paragraph. Power Down (PD) instruction. The Power Down instruction uses one write cycle to put the memory into a power down mode where current consumption is typically reduced to less than 1.0A. Once in this state, a Reset (RST) command must be written to the P/E.C. prior to any operation.
11/31
12/31
tAVAV VALID tAVQV tELQV tAXQX
M29W040
Figure 6. Read Mode AC Waveforms
A0-A18
E tEHQZ tELQX tEHQX
G tGLQV tGLQX VALID tGHQX tGHQZ
DQ0-DQ7
OUTPUT ENABLE
DATA VALID
AI01363B
ADDRESS VALID AND CHIP ENABLE
Note: Write Enable (W) = High
M29W040
Table 13A. Write AC Characteristics, Write Enable Controlled (TA = 0 to 70C, -20 to 85C or -40 to 85C)
M29W040 Symbol Alt Parameter -100 VCC = 3.3V0.3V CL = 30pF Min tAVAV tELWL tWLWH tDVWH tWHDX tWHEH tWHWL tAVWL tWLAX tGHWL tVCHEL tWHQV1 tWHQV2 tWHGL
(1)
-120 VCC = 3.3V0.3V Min 120 0 50 50 0 0 30 0 50 0 50 12 30 1.5 0 30 Max
Unit
Max
tWC tCS tWP tDS tDH tCH
Address Valid to Next Address Valid Chip Enable Low to Write Enable Low Write Enable Low to Write Enable High Input Valid to Write Enable High Write Enable High to Input Transition Write Enable High to Chip Enable High
100 0 45 45 0 0 25 0 45 0 50 12 1.5 0
ns ns ns ns ns ns ns ns ns ns s s sec ns
tWPH Write Enable High to Write Enable Low tAS tAH Address Valid to Write Enable Low Write Enable Low to Address Transition Output Enable High to Write Enable Low tVCS VCC High to Chip Enable Low Write Enable High to Output Valid (Program) Write Enable High to Output Valid (Block Erase) tOEH Write Enable High to Output Enable Low
(1)
Note: 1. Time is measured to Data Polling or Toggle Bit, t WHQV = tWHQ7V + tQ7VQV.
Chip Erase(CE) instruction. This instructionuses six write cycles. The Erase Set-up command 80h is written to address 5555h on third cycle after the two coded cycles. The Chip Erase Confirm command 10h is written at address5555h on sixth cycle after another two coded cycles. If the second command given is not an erase confirm or if the coded cycles are wrong, the instruction aborts and the device is reset to Read Array. It is not necessaryto program the array with 00h first as the P/E.C. will automatically do this before erasing to FFh. Read operations after the sixth rising edge of W or E
output the status register bits. During the execution of the erase by the P/E.C. the memory will not accept any instruction. Read of DataPolling bit DQ7 returns '0', then '1' on completion. The Toggle Bit DQ6 toggles during erase operation and stops when erase is completed. After completion the Status Register bit DQ5 returns '1' if there has been an Erase Failure because the erasure has not been verified even after the maximum number of erase cycles have been executed.
13/31
M29W040
Table 13B. Write AC Characteristics, Write Enable Controlled (TA = 0 to 70C, -20 to 85C or -40 to 85C)
M29W040 Symbol Alt Parameter -150 VCC = 2.7V to 3.6V Min tAVAV tELWL tWLWH tDVWH tWHDX tWHEH tWHWL tAVWL tWLAX tGHWL tVCHEL tWHQV1
(1)
-200 VCC = 2.7V to 3.6V Min 200 0 80 80 0 0 35 0 65 0 50 12 30 1.5 0 30 Max
Unit
Max
tWC tCS tWP tDS tDH tCH
Address Valid to Next Address Valid Chip Enable Low to Write Enable Low Write Enable Low to Write Enable High Input Valid to Write Enable High Write Enable High to Input Transition Write Enable High to Chip Enable High
150 0 65 65 0 0 35 0 65 0 50 12 1.5 0
ns ns ns ns ns ns ns ns ns ns s s sec ns
tWPH Write Enable High to Write Enable Low tAS tAH Address Valid to Write Enable Low Write Enable Low to Address Transition Output Enable High to Write Enable Low tVCS VCC High to Chip Enable Low Write Enable High to Output Valid (Program) Write Enable High to Output Valid (Block Erase) tOEH Write Enable High to Output Enable Low
tWHQV2 (1) tWHGL
Note: 1. Time is measured to Data Polling or Toggle Bit, tWHQV = tWHQ7V + tQ7VQV.
Block Erase (BE) instruction. This instruction uses a minimum of six write cycles. The Erase Set-up command 80h is written to address 5555h on third cycle after the two coded cycles. The Block Erase Confirm command 30h is written on sixth cycle after another two coded cycles. During the input of the second command an address within the block to be erased is given and latched into the memory. Additional Block Erase confirm commands and block addresses can be written subsequently to erase other blocks in parallel, without further coded cycles. The erase will start after the Erase timeout period (see Erase Timer Bit DQ3 description). Thus, additional Block Erase commands must be given within this delay. The input of a newBlock Erasecommand will restart the timeout period. The status of the internal timer can be monitored through the level of DQ3, if DQ3 is '0' the Block Erase Command has been given and the timeout is running, if DQ3 is '1', the timeout has expired and the P/E.C is erasing the block(s).
During Erase timeout, any command different from 30h will abort the instruction and reset the device to read array mode. It is not necessary to program the block with 00h as the P/E.C. will do this automatically before erasing to FFh. Read operations after the sixth rising edge of W or E output the status register bits. During the executionof the erase by the P/E.C.,the memory accepts only the ES (Erase Suspend) and RST (Reset) instructions. Data Polling bit DQ7 returns '0' while the erasure is in progress and '1' when it has completed.The Toggle Bit DQ6 toggles during the erase operation. It stops when erase is completed. After completion the Status Register bit DQ5 returns '1' if there has been an Erase Failure because erasure has not completed even after the maximum number of erase cycles have been executed. In this case, it will be necessary to input a Reset (RST) to the command interface in order to reset the P/E.C.
14/31
M29W040
Figure 7. Write AC Waveforms, W Controlled
WRITE CYCLE A0-A18 VALID tWLAX tAVWL E tELWL G tGHWL W tWHWL tDVWH DQ0-DQ7 VALID tWHDX tWLWH tWHGL tWHEH
VCC tVCHEL
AI01365B
Note: Address are latched on the falling edge of W, Data is latched on the rising edge of W.
Program (PG) instruction. The memory can be programmed Byte-by-Byte. This instruction uses four write cycles. The Program command A0h is written on the third cycle after two coded cycles. A fourth write operation latches the Address on the falling edge of W or E and the Data to be written on its rising edge and starts the P/E.C. During the execution of the program by the P/E.C., the memory will not acceptany instruction.Read operations output the status bits after the programming has started. The status bits DQ5, DQ6 and DQ7 allow a checkof the statusof the programmingoperation. Memory programming is made only by writing '0' in place of '1' in a Byte. Erase Suspend (ES) instruction. The Block Erase operation may be suspended by this instruction which consists of writing the command B0h without any specific addresscode. No codedcycles are required.It allows reading of data from another block while erase is in progress. Erase suspend is accepted only during the Block Erase instruction execution and defaults to read array mode. Writing
this command during Erase timeout will, in addition to suspending the erase, terminate the timeout. The Toggle Bit DQ6 stops toggling when the P/E.C. is suspended. ToggleBit status must be monitored at an address out of the block being erased. Toggle Bit will stop toggling between 0.1s and 15s after the Erase Suspend (ES) command has been written. The M29W040 will then automatically set to Read Memory Array mode. When erase is suspended, Read from blocks being erased will output invalid data, Read from block not being erased is valid. During the suspension the memory will respond only to Erase Resume (ER) and Reset (RST) instructions. RST command will definitively abort erasure and result in the invalid data in the blocks being erased. Erase Resume (ER) instruction. If an Erase Suspend instruction was previously executed, the erase operation may be resumed by giving the command 30h, at any address, and without any coded cycles.
15/31
M29W040
Table 14A. Write AC Characteristics, Chip Enable Controlled (TA = 0 to 70C, -20 to 85C or -40 to 85C)
M29W040 Symbol Alt Parameter -100 VCC = 3.3V0.3V C L = 30pF Min tAVAV tWLEL tELEH tDVEH tEHDX tEHWH tEHEL tAVEL tELAX tGHEL tVCHWL tEHQV1 tEHQV2
(1)
-120 VCC = 3.3V0.3V Min 120 0 50 50 0 0 30 0 50 0 50 12 30 1.5 0 30 Max
Unit
Max
tWC tWS tCP tDS tDH tWH tCPH tAS tAH
Address Valid to Next Address Valid Write Enable Low to Chip Enable Low Chip Enable Low to Chip Enable High Input Valid to Chip Enable High Chip Enable High to Input Transition Chip Enable High to Write Enable High Chip Enable High to Chip Enable Low Address Valid to Chip Enable Low Chip Enable Low to Address Transition Output Enable High Chip Enable Low
100 0 45 45 0 0 25 0 45 0 50 12 1.5 0
ns ns ns ns ns ns ns ns ns ns s s sec ns
tVCS
VCC High to Write Enable Low Chip Enable High to Output Valid (Program) Chip Enable High to Output Valid (Block Erase)
(1)
tEHGL
tOEH
Chip Enable High to Output Enable Low
Note: 1. Time is measured to Data Polling or Toggle Bit, tWHQV = tWHQ7V + tQ7VQV.
Power Up The memory Command Interfaceis reseton power up to Read Array. Either E or W must be tied to VIH during Power-up to allow maximum security and the possibility to write a command on the first rising adge of E or W. Any write cycle initiation is blocked when VCC is below VLKO.
Supply Rails Normal precautions must be taken for supply voltage decoupling, each device in a system should have the VCC rail decoupledwith a 1.0F capacitor close to the VCC and VSS pins. The PCB trace widths should be sufficient to carry the VCC program and erase currents required.
16/31
M29W040
Table 14B. Write AC Characteristics, Chip Enable Controlled (TA = 0 to 70C, -20 to 85C or -40 to 85C)
M29W040 Symbol Alt Parameter -150 -200 Unit
VCC = 2.7V to 3.6V VCC = 2.7V to 3.6V Min tAVAV tWLEL tELEH tDVEH tEHDX tEHWH tEHEL tAVEL tELAX tGHEL tVCHWL tEHQV1
(1)
Max
Min 200 0 80 80 0 0 35 0 65 0 50 12
Max ns ns ns ns ns ns ns ns ns ns s s 30 sec ns
tWC tWS tCP tDS tDH tWH tCPH tAS tAH
Address Valid to Next Address Valid Write Enable Low to Chip Enable Low Chip Enable Low to Chip Enable High Input Valid to Chip Enable High Chip Enable High to Input Transition Chip Enable High to Write Enable High Chip Enable High to Chip Enable Low Address Valid to Chip Enable Low Chip Enable Low to Address Transition Output Enable High Chip Enable Low
150 0 65 65 0 0 35 0 65 0 50 12 1.5 0 30
tVCS
VCC High to Write Enable Low Chip Enable High to Output Valid (Program) Chip Enable High to Output Valid (Block Erase)
tEHQV2 (1) tEHGL tOEH
1.5 0
Chip Enable High to Output Enable Low
Note: 1. Time is measured to Data Polling or Toggle Bit, t WHQV = tWHQ7V + tQ7VQV.
17/31
M29W040
Figure 8. Write AC Waveforms, E Controlled
WRITE CYCLE A0-A18 VALID tELAX tAVEL W tWLEL G tGHEL E tEHEL tDVEH DQ0-DQ7 VALID tEHDX tELEH tEHGL tEHWH
VCC tVCHWL
AI01366B
Note: Address are latched on the falling edge of E, Data is latched on the rising edge of E.
18/31
M29W040
Table 15A. Data Polling and Toggle Bit AC Characteristics (1) (TA = 0 to 70C, -20 to 85C or -40 to 85C)
M29W040 Symbol Alt Parameter -100 VCC = 3.3V0.3V C L = 30pF Min tWHQ7V1 (2) tWHQ7V2 (2) tEHQ7V1 (2) tEHQ7V2 (2) tQ7VQV tWHQV1 tWHQV2 tEHQV1 tEHQV2 Write Enable High to DQ7 Valid (Program, W Controlled) Write Enable High to DQ7 Valid (Block Erase, W Controlled) Chip Enable High to DQ7 Valid (Program, E Controlled) Chip Enable High to DQ7 Valid (Block Erase, E Controlled) Q7 Valid to Output Valid (Data Polling) Write Enable High to Output Valid (Program) Write Enable High to Output Valid (Block Erase) Chip Enable High to Output Valid (Program) Chip Enable High to Output Valid (Block Erase) 12 1.5 12 1.5 30 30 12 1.5 12 1.5 30 45 12 1.5 12 1.5 30 30 30 Max -120 VCC = 3.3V0.3V Min 12 1.5 12 1.5 30 50 30 Max s sec s sec ns s sec s sec Unit
Notes: 1. All other timings are defined in Read AC Characteristics table. 2. tWHQ7V is the Program or Erase time.
19/31
M29W040
Table 15B. Data Polling and Toggle Bit AC Characteristics (1) (TA = 0 to 70C, -20 to 85C or -40 to 85C)
M29W040 Symbol Alt Parameter -150 VCC = 2.7V to 3.6V Min tWHQ7V1 (2) tWHQ7V2 (2) tEHQ7V1 (2) tEHQ7V2 (2) tQ7VQV tWHQV1 tWHQV2 tEHQV1 tEHQV2 Write Enable High to DQ7 Valid (Program, W Controlled) Write Enable High to DQ7 Valid (Block Erase, W Controlled) Chip Enable High to DQ7 Valid (Program, E Controlled) Chip Enable High to DQ7 Valid (Block Erase, E Controlled) Q7 Valid to Output Valid (Data Polling) Write Enable High to Output Valid (Program) Write Enable High to Output Valid (Block Erase) Chip Enable High to Output Valid (Program) Chip Enable High to Output Valid (Block Erase) 12 1.5 12 1.5 30 30 12 1.5 12 1.5 30 55 12 1.5 12 1.5 30 30 30 Max -200 VCC = 2.7V to 3.6V Min 12 1.5 12 1.5 30 70 30 Max s sec s sec ns s sec s sec Unit
Notes: 1. All other timings are defined in Read AC Characteristics table. 2. tWHQ7V is the Program or Erase time.
20/31
DATA OUTPUT VALID BYTE ADDRESS (WITHIN BLOCKS) tAVQV tELQV
A0-A18
E tEHQ7V
Figure 9. Data Polling DQ7 AC Waveforms
G tGLQV
W tWHQ7V DQ7 VALID
DQ7
DQ0-DQ6
IGNORE tQ7VQV
VALID
LAST CYCLE OF PROGRAM OR ERASE
DATA POLLING READ CYCLES
DATA POLLING (LAST) CYCLE
DATA VERIFY READ CYCLE
AI01364B
M29W040
Notes: 1. 2. 3. 4.
All other timings are as a normal Read cycle. DQ7 and DQ0-DQ6 can transmit to valid at any point during the data output valid period. tWHQ7V is the Program or Erase time. During erasing operation Byte address must be within Block being erased.
21/31
M29W040
Figure 10. Data Polling Flowchart Figure 11. Data Toggle Flowchart
START
START
READ DQ5 & DQ7 at VALID ADDRESS
READ DQ5 & DQ6
DQ7 = DATA NO NO
YES
DQ6 = TOGGLE YES NO
NO
DQ5 =1 YES READ DQ7
DQ5 =1 YES READ DQ6
DQ7 = DATA NO FAIL
YES
DQ6 = TOGGLE YES PASS FAIL
NO
PASS
AI01369
AI01370
Table 16. Program, Erase Times and Program, Erase Endurance Cycles (TA = 0 to 70C; VCC = 2.7V to 3.6V)
Parameter Min Chip Program (Byte) Chip Erase (Preprogrammed) Chip Erase Block Erase (Preprogrammed) Block Erase Byte Program Program/Erase Cycles (per Block) 12 100,000 M29W040 Typ 6 2.5 8.5 1.5 2 2200 30 30 Max sec sec sec sec sec s cycles Unit
22/31
A0-A18 VALID tEHQV tAVQV
E tELQV
Figure 12. Data Toggle DQ6 AC Waveforms
G tGLQV
W tWHQV STOP TOGGLE VALID
DQ6
DQ0-DQ5, DQ7 IGNORE
VALID
LAST CYCLE OF PROGRAM OF ERASE
DATA TOGGLE READ CYCLE
DATA TOGGLE READ CYCLE
READ CYCLE
AI01367
M29W040
Note: All other timings are as a normal Read cycle.
23/31
M29W040
Figure 13. Block Protection Flowchart
START
BLOCK ADDRESS on A16, A17, A18
n=0
G, A9 = VID, E = VIL Wait 4s W = VIL Wait 100s W = VIH G = VIH Wait 4s
READ DQ0 at PROTECTION ADDRESS: A0, A6 = VIL, A1 = VIH and A16, A17, A18 DEFINING BLOCK
DQ0 =1 YES A9 = VIH PASS
NO
++n = 25 YES A9 = VIH FAIL
NO
AI01368D
24/31
M29W040
Figure 14. Block Unprotecting Flowchart
START PROTECT ALL BLOCKS
n=0 A6, A12, A16 = VIH E, G, A9 = VIH
Wait 4s
E, G, A9 = VID Wait 4s W = VIL Wait 10ms W = VIH E, G = VIH Wait 4s
READ at UNPROTECTION ADDRESS: A1, A6 = VIH, A0 = VIL and A16, A17, A18 DEFINING BLOCK (see Note 1)
INCREMENT BLOCK
NO
DATA = 00h
YES
NO
++n = 1000 YES FAIL
LAST SECT. YES PASS
NO
AI01371E
Note: 1. A6 is kept at VIH during unprotection algorithm in order to secure best unprotection verification. During all other protection status reads, A6 must be kept at VIL.
25/31
M29W040
ORDERING INFORMATION SCHEME Example: M29W040 -120 N 1 TR
Operating Voltage W 2.7V to 3.6V -100 -120 -150 -200
Speed
(1)
Package K N PLCC32 TSOP32 8 x 20mm
Temp. Range 1 5 6 0 to 70 C -20 to 85 C -40 to 85 C R
Option Reverse Pinout
100ns 120ns 150ns 200ns
NZ TSOP32 8 x 14mm
TR Tape & Reel Packing
Note: 1. This speed is obtained with a supply voltage range of V CC = 3.3V 0.3V and a load capacitance at 30pF.
M29W040 is replaced by the new version M29W040B Device are shipped from the factory with the memory content erased (to FFh). For a list of available options(Speed, Package,etc...) or for further information on any aspect of this device, please contact the STMicroelectronics Sales Office nearest to you.
26/31
M29W040
PLCC32 - 32 lead Plastic Leaded Chip Carrier, rectangular
Symb Typ A A1 A2 B B1 D D1 D2 E E1 E2 e F R N Nd Ne CP 0.89 1.27 mm Min 2.54 1.52 - 0.33 0.66 12.32 11.35 9.91 14.86 13.89 12.45 - 0.00 - 32 7 9 0.10 Max 3.56 2.41 0.38 0.53 0.81 12.57 11.56 10.92 15.11 14.10 13.46 - 0.25 - 0.035 0.050 Typ inches Min 0.100 0.060 - 0.013 0.026 0.485 0.447 0.390 0.585 0.547 0.490 - 0.000 - 32 7 9 0.004 Max 0.140 0.095 0.015 0.021 0.032 0.495 0.455 0.430 0.595 0.555 0.530 - 0.010 -
D D1
1N
A1 A2
B1
Ne
E1 E
F 0.51 (.020)
D2/E2 B
e
1.14 (.045)
Nd
A R CP
PLCC
Drawing is not to scale.
27/31
M29W040
TSOP32 Normal Pinout - 32 lead Plastic Thin Small Outline, 8 x 20mm
Symb Typ A A1 A2 B C D D1 E e L N CP 0.50 0.05 0.95 0.15 0.10 19.80 18.30 7.90 0.50 0 32 0.10 mm Min Max 1.20 0.15 1.05 0.27 0.21 20.20 18.50 8.10 0.70 5 0.020 0.002 0.037 0.006 0.004 0.780 0.720 0.311 0.020 0 32 0.004 Typ inches Min Max 0.047 0.007 0.041 0.011 0.008 0.795 0.728 0.319 0.028 5
A2
1 N
e E B
N/2
D1 D
A CP
DIE
C
TSOP-a
Drawing is not to scale.
A1
L
28/31
M29W040
TSOP32 Reverse Pinout - 32 lead Plastic Thin Small Outline, 8 x 20mm
Symb Typ A A1 A2 B C D D1 E e L N CP 0.50 0.05 0.95 0.15 0.10 19.80 18.30 7.90 - 0.50 0 32 0.10 mm Min Max 1.20 0.17 1.05 0.27 0.21 20.20 18.50 8.10 - 0.70 5 0.020 0.002 0.037 0.006 0.004 0.780 0.720 0.311 - 0.020 0 32 0.004 Typ inches Min Max 0.047 0.006 0.041 0.011 0.008 0.795 0.728 0.319 - 0.028 5
A2
1 N
e E B
N/2
D1 D
A CP
DIE
C
TSOP-b
Drawing is not to scale.
A1
L
29/31
M29W040
TSOP32 - 32 lead Plastic Thin Small Outline, 8 x 14mm
Symb Typ A A1 A2 B C D D1 E e L N CP 0.50 0.05 0.95 0.17 0.10 13.80 12.30 7.90 0.50 0 32 0.10 mm Min Max 1.20 0.15 1.05 0.27 0.21 14.20 12.50 8.10 0.70 5 0.020 0.002 0.037 0.007 0.004 0.543 0.484 0.311 0.020 0 32 0.004 Typ inches Min Max 0.047 0.006 0.041 0.011 0.008 0.559 0.492 0.319 0.028 5
A2
1 N
e E B
N/2
D1 D
A CP
DIE
C
TSOP-a
Drawing is not to scale.
A1
L
30/31
M29W040
Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics (c) 1999 STMicroelectronics - All Rights Reserved All other names are the property of their respective owners. STMicroelectronics GROUP OF COMPANIES Australia - Brazil - China - Finland - France - Germany - Hong Kong - India - Italy - Japan - Malaysia - Malta - Morocco Singapore - Spain - Sweden - Switzerland - United Kingdom - U.S.A. http://www.st.com
31/31

▲Up To Search▲

Price & Availability of M29W040

	To Download M29W040 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .